Coolpad Catalyst 3622a - Unbrick Quest

Hello XDA!

I'm on a quest to unbrick a Coolpad Catalyst 3622a. I'm going to list what I have compiled to aide me with a question at the end.
My phone is currently in QDLoader 9008 mode. Dead as dead can get.

Correct me if I am wrong here but I need to get the phone into QDLoader 9006 mode to accomplish a flash.

What I have compiled is a rom dump of a working Coolpad Catalyst 3622a.

Code:

-rw-rw-rw- 1 don 0 524288 2017-01-12 21:00 tz-rw-rw-rw- 1 don 0 524288 2017-01-12 21:00 tzbak-rw-rw-rw- 1 don 0 1825361920 2017-01-12 21:00 system-rw-rw-rw- 1 don 0 524288 2017-01-12 20:57 rpm-rw-rw-rw- 1 don 0 524288 2017-01-12 20:57 rpmbak-rw-rw-rw- 1 don 0 524288 2017-01-12 20:57 sbl1-rw-rw-rw- 1 don 0 524288 2017-01-12 20:57 sbl1bak-rw-rw-rw- 1 don 0 16384 2017-01-12 20:57 sec-rw-rw-rw- 1 don 0 8192 2017-01-12 20:57 ssd-rw-rw-rw- 1 don 0 16777216 2017-01-12 20:57 recovery-rw-rw-rw- 1 don 0 33554432 2017-01-12 20:57 persist-rw-rw-rw- 1 don 0 1048576 2017-01-12 20:57 params-rw-rw-rw- 1 don 0 20971520 2017-01-12 20:57 panic-rw-rw-rw- 1 don 0 1572864 2017-01-12 20:57 modemst2-rw-rw-rw- 1 don 0 1048576 2017-01-12 20:57 oem-rw-rw-rw- 1 don 0 1048576 2017-01-12 20:57 pad-rw-rw-rw- 1 don 0 67108864 2017-01-12 20:57 modem-rw-rw-rw- 1 don 0 1572864 2017-01-12 20:57 modemst1-rw-rw-rw- 1 don 0 1024 2017-01-12 20:57 fsc-rw-rw-rw- 1 don 0 1572864 2017-01-12 20:57 fsg-rw-rw-rw- 1 don 0 524288 2017-01-12 20:57 keystore-rw-rw-rw- 1 don 0 1048576 2017-01-12 20:57 misc-rw-rw-rw- 1 don 0 268435456 2017-01-12 20:57 cache-rw-rw-rw- 1 don 0 524288 2017-01-12 20:57 config-rw-rw-rw- 1 don 0 32768 2017-01-12 20:57 DDR-rw-rw-rw- 1 don 0 1048576 2017-01-12 20:57 devinfo-rw-rw-rw- 1 don 0 16777216 2017-01-12 20:56 boot-rw-rw-rw- 1 don 0 3145728 2017-01-12 20:56 aboot-rw-rw-rw- 1 don 0 3145728 2017-01-12 20:56 abootbak

I have also obtained the partition.xml which I also think is needed.

Code:

Model: MMC FN12MB (sd/mmc)Disk /dev/block/mmcblk0: 7818MBSector size (logical/physical): 512B/512BPartition Table: gptNumber Start End Size File system Name Flags 1 17.4kB 542kB 524kB sbl1 2 542kB 1066kB 524kB sbl1bak 3 1066kB 4212kB 3146kB aboot 4 4212kB 7357kB 3146kB abootbak 5 7357kB 7882kB 524kB rpm 6 7882kB 8406kB 524kB rpmbak 7 8406kB 8930kB 524kB tz 8 8930kB 9455kB 524kB tzbak 9 9455kB 10.5MB 1049kB pad10 10.5MB 12.1MB 1573kB modemst111 12.1MB 13.6MB 1573kB modemst212 13.6MB 14.7MB 1049kB misc13 14.7MB 15.7MB 1049kB params14 15.7MB 36.7MB 21.0MB ext4 panic15 36.7MB 36.7MB 1024B fsc16 36.7MB 36.7MB 8192B ssd17 36.7MB 37.3MB 524kB keystore18 37.3MB 37.8MB 524kB config19 37.8MB 38.8MB 1049kB oem20 41.9MB 109MB 67.1MB fat16 modem21 109MB 110MB 1049kB devinfo22 110MB 110MB 32.8kB DDR23 110MB 112MB 1573kB fsg24 112MB 128MB 16.8MB boot25 128MB 128MB 16.4kB sec26 128MB 1954MB 1825MB ext4 system27 1954MB 1987MB 33.6MB ext4 persist28 1987MB 2256MB 268MB ext4 cache29 2256MB 2273MB 16.8MB recovery30 2273MB 7818MB 5546MB ext4 userdata

From reading over the past few days. I have come to the proverbial road block.

1: Use PartitioningTool.py in conjunction with Partition.xml to output rawprogram0.xml as well as patch0.xml.
I have obtained and installed python27. The python executable is system wide.

I'm not 100% sure about what arguments or the command line itself to issue to python in order to produce: rawprogram0.xml and patch0.xml.
I thought it was as simple as passing something like this: python PartitioningTool.py Partition.xml.
If somebody could help me here it would be very much appreciated.

Then I know I have to use emmcldl and partiton.xml to produce the file 8909_msimage.mbn. After words with a lot of luck I use QPST to get the device into QDLoader 9006 mode.

Hopefully then I will be able to flash.

Thanks for reading!

coolpad 3622a revived from the dead....

thanks for the help?